panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ jm asctb184e 201202-t ordering information ideal for compressor and motor control inrush 80a, 1a 20a power relay jm relays vde flat type slim type rohs compliant features ?compact, high-capacity, and resistant to inductive loads it can control an inductive load with inrush current of 80 a and steady state current of 20 a. ?excellent contact welding resistance high contact pressure, a forced opening mechanism, and a forced wiping mechanism realizes an excellent contact welding resistance. ?high breakdown voltage and surge resistant relay more than 6.4 mm .252 inch maintained for the insulation distance between contacts and coil, and the breakdown voltage between contacts and coil is 5,000 v for 1 minute. in addition, the surge resistance between contacts and coil is greater than 10,000 v. ?resistant to external force an absorber mechanism is used on the load terminals, giving a large improvement in characteristics variations caused by the external force during faston placement/removal. ?flux resistance mechanism the terminal area is plugged with resin to prevent ?x seepage during pcb mounting. (tmp type) ?conforms to the various safety standards ul, csa, vde available ?the line up can support economical mounting methods. the relay are equipped with a drive terminal (coil terminal) on one side for pcbs, and a load terminal (tab terminal #250) on the reverse side. the line up includes the tm type which can be attached directly to the pcb composing a drive circuit, and the tmp type which supports economical wiring. the tmp type can also be directly attached, and a high capacity load can be wired to the tab terminal. typical applications ?compressor and heater control in air conditioners ?power control in hot air type heaters ?magnetron control in microwave ovens ?lamp and motor control in oa equipment such as copiers and facsimiles. jm relay jm 1a n f pickup voltage n: 70% of nominal voltage classification of type nil: z: slim type flat type mounting classification tmp: tm: p: tmp type tm type (flat type) pcb type (slim type) nominal coil voltage dc5v, dc6v, dc9v, dc12v, dc24v, dc48v contact material f: agsno 2 type contact arrangement 1a: 1 form a note: certified by ul, csa and vde
panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ jm asctb184e 201202-t types standard packing: carton 50 pcs., case 200 pcs. rating 1. coil data 2. speci?ations * speci?ations will vary with foreign standards certi?ation ratings. notes: *1. this value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. *2. wave is standard shock voltage of 1.2 50 s according to jec-212-1981 *3. the upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. refer to usage, transport and storage conditions in notes. 3. switching capacity note: standard ul and csa 1hp, 20a 250vac 1 1 / 2 hp, 20a 125vac nominal coil voltage part no. tmp type (flat) tm type (flat) tmp type (slim) pcb type (slim) 5v dc jm1an-ztmp-dc5v-f jm1an-ztm-dc5v-f jm1an-tmp-dc5v-f jm1an-p-dc5v-f 6v dc jm1an-ztmp-dc6v-f jm1an-ztm-dc6v-f jm1an-tmp-dc6v-f jm1an-p-dc6v-f 9v dc jm1an-ztmp-dc9v-f jm1an-ztm-dc9v-f jm1an-tmp-dc9v-f jm1an-p-dc9v-f 12v dc jm1an-ztmp-dc12v-f jm1an-ztm-dc12v-f jm1an-tmp-dc12v-f JM1AN-P-DC12V-F 24v dc jm1an-ztmp-dc24v-f jm1an-ztm-dc24v-f jm1an-tmp-dc24v-f jm1an-p-dc24v-f 48v dc jm1an-ztmp-dc48v-f jm1an-ztm-dc48v-f jm1an-tmp-dc48v-f jm1an-p-dc48v-f nominal coil voltage pick-up voltage (at 20 c 68 f ) drop-out voltage (at 20 c 68 f ) nominal operating current [ 10%] (at 20 c 68 f ) coil resistance [ 10%] (at 20 c 68 f ) nominal operating power max. applied voltage (at 60 c 140 f ) 5v dc 70%v or less of nominal voltage (initial) 10%v or more of nominal voltage (initial) 180 ma 27.8 ? 900mw 110%v of nominal voltage 6v dc 150 ma 40 ? 9v dc 100 ma 90 ? 12v dc 75 ma 160 ? 24v dc 37.5 ma 640 ? 48v dc 18.75ma 2,560 ? characteristics item speci?ations contact contact material agsno 2 type arrangement 1 form a contact resistance (initial) max. 100 m ? (by voltage drop 6 v dc 1a) rating nominal switching capacity (resistive load) 20a 250v ac max. switching power (resistive load) 5,000va max. switching voltage 250v ac max. switching current 20a min. switching capacity (reference value)* 1 100ma, 5v dc electrical characteristics insulation resistance (initial) min. 100m ? (at 500v dc) measurement at same location as ?reakdown voltage section. breakdown voltage (initial) between open contacts 1,000 vrms for 1 min. (detection current: 10 ma) between contact and coil 5,000 vrms for 1 min. (detection current: 10 ma) temperature rise (coil) max. 55 c 131 f (by resistive method, nominal coil voltage applied to coil: 100%v, contact carrying current: 20a, at 60 c 140 f ) surge breakdown voltage* 2 (between contact and coil) (initial) 10,000 v operate time (at nominal voltage) (at 20 c 68 f ) max. 20 ms (excluding contact bounce time.) release time (at nominal voltage) (at 20 c 68 f ) max. 10 ms (excluding contact bounce time) (without diode) mechanical characteristics shock resistance functional 98 m/s 2 (half-wave pulse of sine wave: 11 ms; detection time: 10 s.) destructive 980 m/s 2 (half-wave pulse of sine wave: 6 ms.) vibration resistance functional 10 to 55 hz at double amplitude of 1.6 mm (detection time: 10 s.) destructive 10 to 55 hz at double amplitude of 2 mm expected life mechanical (at 180 times/min.) min. 10 6 electrical (at 20 times/min.) min. 10 5 (at nominal switching capacity) conditions conditions for operation, transport and storage* 3 ambient temperature: ?0 c to +60 c ?0 f to +140 f , humidity: 5 to 85% r.h. (not freezing and condensing at low temperature) max. operating speed 20 times/min. (at nominal switching capacity) unit weight slim tmp and slim pcb: approx. 28 g .99 oz flat tmp: approx. 30 g 1.06 oz flat tm: approx. 30 g 1.06 oz electrical life resistive load 20 a, 250 v ac (cos = 1) 10 5 (at 20 times/min.) inductive load (cos = 0.7) inrush 70 a, steady 20 a (250 v ac cos = 0.7) 10 5 (at 20 times/min.) inrush 80 a, cut-off 80 a (when the motor is locked) (250 v ac cos = 0.7) 1.5 10 3 (at 20 times/min.)
panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ jm asctb184e 201202-t reference data dimensions (mm inch ) 1. coil temperature rise place to be measured: inside of coil ambient temperature: 25 c 77 f 2. life curve 3. operate/release time sample: jm1an-tmp-dc24v-f, 5 pcs. 20a 0a 80 90 100 110 120 130 60 50 40 30 20 0 coil applied voltage, %v temperature rise, c 100 10 50 5101520 250v ac resistive load contact current, a life, 10 4 x min. min. x x - max. operate time release time max. 80 90 100 110 120 130 14 13 12 11 10 9 8 7 6 5 4 3 2 0 coil applied voltage, %v operate/release time, ms - 4. ambient temperature characteristics sample: jm1an-tmp-dc24v-f, 5 pcs. ?0 ?0 ?0 20 10 30 ?0 ?0 0 40 60 8020 drop-out voltage pick-up voltage ambient temperature, c change, % the cad data of the products with a cad data mark can be downloaded from: http://industrial.panasonic.com/ac/e/ flat tmp type external dimensions comn.o. 31 28.5 18 17 6.2 9.9 15 2.15 6.8 6.35 0.8 8 1.5 1 4.5 243.5 9.2 5 6 12 n.o. com 17.2 0.2 faston 250 1.220 1.122 .709 .669 .224 .390 .591 .085 .268 .250 .031 .315 .059 .039 .177 .945.138 .362 .677 .008 schematic com com coil n.o. faston 250 pc board side n.o. pc board pattern (bottom view) tolerance: 0.1 .004 2.5 0.1 2.15 5.2 com n.o. coil 1.8 dia. 22 0.1 20 0.1 24.5 0.1 .098 .004 .085 .205 .071 dia. 2.0 dia. .079 dia. 2.0 dia. .079 dia. 1.8 dia. .071 dia. .866 .004 .787 .004 .965 .004 cad data general tolerance: 0.4 .016
panasonic corporation automation controls business unit industrial.panasonic.com/ac/e/ jm asctb184e 201202-t safety standards for cautions f or us e . item ul/c-ul (recognized) csa (certi?d) vde (certi?d) file no. contact rating file no. contact rating file no. contact rating slim type e43028 20a 125v ac 20a 250v ac 1 1 / 2 hp 125v ac 1hp 250v ac lr26550 20a 125v ac 20a 250v ac 1 1 / 2 hp 125v ac 1hp 250v ac 40014275 20a 250v ac (cos =1.0) 12a 220v ac (cos =0.4) flat type e43028 20a 125v ac 20a 250v ac 1 1 / 2 hp 125v ac 1hp 250v ac lr26550 20a 125v ac 20a 250v ac 1 1 / 2 hp 125v ac 1hp 250v ac 40014275 20a 250v ac (cos =1.0) 12a 230v ac (cos =0.4) flat tm type external dimensions comn.o. 31 11.2 10 47.5 28.5 4.5 17.6 9.9 15 2.15 6.8 6.35 0.8 0.5 1.85 8 1.5 0.6 16.8 faston 250 faston 187 2 39.5 r2.25 8.2 1.220 .441 .394 1.870 1.122 .177 .693 .390 .591 .085 .268 .250 .031 .020 .073 .315 .059 .024 .661 .079 1.555 .323 r.088 schematic com coil faston 250 faston 187 n.o. panel cutout 39.5 0.1 2-4.5 0.1 dia. 1.555 .004 2-.177 .004 dia. cad data general tolerance: 0.4 .016 slim tmp type external dimensions 34 12 com 12.9 11 10.012.0 27.6 30.4 26.0 6.0 n.o. 6.35 12.0 16.0 1.8 26.0 0.5 4.0 10.0 .508 .433 .394.472 1.087 1.197 1.024 .236 .250 .472 .630 .071 1.024 .020 .157 .394 schematic faston 250 pc board side comn.o. pc board pattern (copper-side view) tolerance: 0.1 .004 12.0 0.1 10.0 0.1 12.0 0.1 27.6 0.1 13.8 0.1 2.0 0.1 dia. .079 .004 dia. 2.0 0.1 dia. .079 .004 dia. 1.8 0.1 dia. .071 .004 dia. 1.8 0.1 dia. .071 .004 dia. .472 .004 .394 .004 .472 .004 1.087 .004 .543 .004 cad data general tolerance: 0.4 .016 slim pcb type external dimensions 34 12 com 10.012.0 27.6 30.4 26.0 6.0 n.o. 12.0 16.0 1.8 26.0 0.5 4.0 .394.472 1.087 1.197 1.024 .236 .472 .630 .071 1.024 .020 .157 schematic pc board side comn.o. pc board pattern (copper-side view) tolerance: 0.1 .004 12.0 0.1 10.0 0.1 12.0 0.1 27.6 0.1 13.8 0.1 2.0 0.1 dia. .079 .004 dia. 2.0 0.1 dia. .079 .004 dia. 1.8 0.1 dia. .071 .004 dia. 1.8 0.1 dia. .071 .004 dia. .472 .004 .394 .004 .472 .004 1.087 .004 .543 .004 cad data general tolerance: 0.4 .016
|
